3D Wall Panels Installation Method
Wall panel
A paneling is a single piece of fabric, sometimes flat and removes an oblong form, that is visible and exposed covering for a wall. Wall panels area unit useful likewise as ornamental, providing insulation and soundproofing, combined with uniformity of look, alongside some live of sturdiness or easy exchangeability. whereas there's no set size limit for a bit of fabric fulfilling these functions, the most sensible size for wall panels has been prompt to be twenty-four inches by eight feet, to permit for transportation.
Use of wall panels will scale back construction prices by providing a uniform look to the paneled surface while not requiring the applying of paint or another finishing material. Wall panels could also be finished on only 1 aspect if the opposite aspect goes to be against a brick or concrete wall, or a comparable structure. Alternately, the panels might if assembled to associate degree acceptable framework, substitute for having the other reasonably wall in the least. Holes could also be cut or trained into a paneling to accommodate electrical retailers and alternative devices setting out of the wall.
There is a brand new kind of eco-friendly 3d paneling created out of the fibrous residue of sugarcane. This fiber of crushed sugarcane stalks, remaining once raw sugar is extracted from the juice of the sugarcane by shredding it, is currently the material, known as pulp, that forms the bottom of this simply put in the eco friendly product. The material used for this 3d paneling is 100 percent recycled, compostable and is thus 100 percent perishable.
Installation guide for 3D wall panels
Material needed
Tape measure
Long ruler/yardstick
Pencil
Level
Cleaning material
Pencil
Cutter/Scissors or Utility knife
paintable Caulking or sealer.
Preparation
Clean the wall surface - ensure the wall surfaces area unit clean, dry, smooth, and free from mud, grease, wax, etc.
Smooth out any bumps on the wall.
Patch up any giant holes in the wall.
Clean the rear surface of the panel by wiping it with clean material.
Acclimate the panel to the space temperature for a couple of hours before installation.
Decide how you would like to put on the panel
There are often numerous ways that to put on the panel. as an example, diagonally that makes a “diamond” form, begin from the highest middle, begin from the left middle, begin from the right middle and etc. The directions are going to be similar for all the various layout ideas.
Draw horizontal lines
On the wall, you would like to put in the panel, visually examine the corner wherever the ceiling meets the wall. determine the bottom purpose of the ceiling. (It is common to possess a ceiling that's not dead level or even)
Put a panel up against (leave regarding 1/8” space) the bottom purpose of the ceiling and mark the peak of the panel.
From the marking, draw the amount horizontal line across the wall with the assistance of the amount.
This manner you don’t ought to cut any of the highest row panels once install up against the ceiling. Since it's high and therefore the gap is tiny, it won’t be visible.
If the gap between the panel and therefore the ceiling is simply too visible (not likely), you will fill it in with a further panel.
Draw one level horizontal lines for every row of panels.
Draw vertical lines
Visually examine the left corner wherever the left aspect of the wall meets the opposite wall. determine the corner that's protruded the foremost. (It is common to possess a wall that's not dead even)
Put a panel up against (leave regarding 1/8” space) the foremost protrude purpose of the wall and mark the breadth of the panel.
From the marking, draw the amount vertical line across the wall with the assistance of the amount.
This way you don’t ought to cut any of the left-most column panels once install up against the opposite wall.
Draw one level vertical lines for every panel column.
Once you're done drawing horizontal and vertical lines, you're prepared the lay the 3D Wall Panels.
Laying 3D panel
Grab the primary 3D paneling, peel off the protection of all the double-sided adhesive on the panel.
Be careful to not bit the adhesive as which will scale back its viscosity.
Start from the higher left corner, line up the corner of the panel within the grid drawing. ensure all sides area unit lined up.
Push the panel against future panel thus on minimize the gap between panel. faucet across the panel gently to form positive it's secured to the wall.
Continue with a lot of 3D Wall Panels each horizontally and vertically.
Leave the grid blank if there's an electric outlet that you simply don’t need to hide. The panel is often put in later once it's move expose the plug.
Cutting of panel
To cut the 3D paneling
Live the width/height of the world you would like the cut panel
On the rear of the 3D paneling, you would like to chop, use the ruler/tape live to live and mark wherever to chop.
Draw the road to assist guide wherever to chop.
Use the serious duty cut or utility knife to chop the 3D paneling. The way to cut around the wall outlet
Live the dimensions of the wall outlet.
Identify wherever on the panel you would like to chop, draw a box for the outlet.
Use a utility knife to chop a gap in order that you'll be able to use the cut to chop a hole for the outlet .
The hole you narrow on the panel is going to be regarding zero.5” larger than the wall outlet on both sides. this is often in order that the panel won’t block any plug you employ.
Once the panel is up over the outlet, it'll be hollow round the outlet. To fill the hollow panel, use the wall filler. Push the filler into the hollow a part of the panel and fill it up.
Remove the surplus filler and level it with the cut hole.
Once it's dry, you'll be able to paint over the filler.
Caulking
After all the 3D Wall Panels area unit put in, you will need to seal the gap.
Ensure you employ the white paintable caulking/sealant. it's best to urge the non-shrinkable calking/sealant.
Apply the caulking/sealant to the gap between 3D Wall Panels. Use your finger to push the caulking/sealant into the gap.
Use a wet material to wipe off the surplus caulking/sealant.
Wait a couple of hours for the caulking to dry utterly before painting.
Painting
Depends on your applications, you'll be able to use any indoor or outside water-based or oil-based paint.
For best result, it's advisable that you simply apply the primer 1st, then the highest coat.
Paint is often applied victimization brush, roller or the sprayer. 
